Proper study guides for Avant-garde Cisco CCNA Cisco Certified Network Associate CCNA (803) certified begins with Cisco 200-120 preparation products which designed to deliver the Vivid 200-120 questions by making you pass the 200-120 test at your first time. Try the free 200-120 demo right now.
Q241. - (Topic 8)
Which PPP subprotocol negotiates authentication options?
Q242. - (Topic 8)
At which layer of the OSI model does PPP perform?
A. Layer 2
B. Layer 3
C. Layer 4
D. Layer 5
Q243. - (Topic 5)
Refer to the exhibit.
Which rule does the DHCP server use when there is an IP address conflict?
A. The address is removed from the pool until the conflict is resolved.
B. The address remains in the pool until the conflict is resolved.
C. Only the IP detected by Gratuitous ARP is removed from the pool.
D. Only the IP detected by Ping is removed from the pool.
E. The IP will be shown, even after the conflict is resolved.
Q244. - (Topic 1)
Refer to the graphic.
Host A is communicating with the server. What will be the source MAC address of the frames received by Host A from the server?
A. the MAC address of router interface e0
B. the MAC address of router interface e1
C. the MAC address of the server network interface
D. the MAC address of host A
Q245. - (Topic 7)
Refer to the topology. Your company has connected the routers R1. R2. and R3 with serial
links. R2 and R3 are connected to the switches SW1 and SW2, respectively. SW1 and
SW2 are also connected to the routers R4 and R5.
The EIGRP routing protocol is configured.
You are required to troubleshoot and resolve the EIGRP issues between the various
Use the appropriate show commands to troubleshoot the issues.
The loopback interfaces on R4 with the IP addresses of 10.4.4.4 /32, 10.4.4.5/32. and 10.4.4.6/32 are not appearing in the routing table of R5 Why are the interfaces missing?
A. The interfaces are shutdown, so they are not being advertised.
B. R4 has been incorrectly configured to be in another AS, so it does not peer with R5.
C. Automatic summarization is enabled, so only the 10.0.0.0 network is displayed.
D. The loopback addresses haven't been advertised, and the network command is missing on R4.
Q246. CORRECT TEXT - (Topic 7)
Answer: Corp1>enable Corp1#configure terminal Corp1(config)#access-list 100 permit tcp host 192.168.33.3 host 172.22.242.23 eq 80 Corp1(config)#access-list 100 deny tcp 192.168.33.0 0.0.0.255 host 172.22.242.23 eq
Corp1(config)#access-list 100 permit ip any any Corp1(config)#interface fa 0/1 sh ip int brief Corp1(config-if)#ip access-group 100 out Corp1(config-if)#end Corp1#copy running-config startup-config
Q247. - (Topic 3)
Refer to the exhibit.
A network administrator is adding two new hosts to SwitchA. Which three values could be used for the configuration of these hosts? (Choose three.)
A. host A IP address: 192.168.1.79
B. host A IP address: 192.168.1.64
C. host A default gateway: 192.168.1.78
D. host B IP address: 192.168.1.128
E. host B default gateway: 192.168.1.129
F. host B IP address: 192.168.1.190
Q248. - (Topic 8)
The command frame-relay map ip 10.121.16.8 102 broadcast was entered on the router. Which of the following statements is true concerning this command?
A. This command should be executed from the global configuration mode.
B. The IP address 10.121.16.8 is the local router port used to forward data.
C. 102 is the remote DLCI that will receive the information.
D. This command is required for all Frame Relay configurations.
E. The broadcast option allows packets, such as RIP updates, to be forwarded across the PVC.
Q249. - (Topic 9)
What is the effect of the overload keyword in a static NAT translation configuration?
A. It enables port address translation.
B. It enables the use of a secondary pool of IP addresses when the first pool is depleted.
C. It enables the inside interface to receive traffic.
D. It enables the outside interface to forward traffic.
Q250. - (Topic 2)
Refer to the exhibit.
A technician has installed SwitchB and needs to configure it for remote access from the management workstation connected to SwitchA. Which set of commands is required to accomplish this task?
A. SwitchB(config)# interface FastEthernet 0/1 SwitchB(config-if)# ip address 192.168.8.252 255.255.255.0 SwitchB(config-if)# no shutdown
B. SwitchB(config)# interface vlan 1 SwitchB(config-if)# ip address 192.168.8.252 255.255.255.0 SwitchB(config-if)# ip default-gateway 192.168.8.254 255.255.255.0 SwitchB(config-if)# no shutdown
C. SwitchB(config)# ip default-gateway 192.168.8.254 SwitchB(config)# interface vlan 1 SwitchB(config-if)# ip address 192.168.8.252 255.255.255.0 SwitchB(config-if)# no shutdown
D. SwitchB(config)# ip default-network 192.168.8.254 SwitchB(config)# interface vlan 1 SwitchB(config-if)# ip address 192.168.8.252 255.255.255.0 SwitchB(config-if)# no shutdown
E. SwitchB(config)# ip route 192.168.8.254 255.255.255.0 SwitchB(config)# interface FastEthernet 0/1 SwitchB(config-if)# ip address 192.168.8.252 255.255.255.0 SwitchB(config-if)# no shutdown
To know more about the 200-120, click here.