Everyone is absolve to decide on every qualifications examinations that they believe almost all suitalbe to themselves, however , they?¡¥d do not subscribe previous to many people comprehend the locates, a maket-oriented industry and also the property value a qualifications, in lieu of without research go through wave. The most crucial point is usually to decide on qualifications evaluation reported by you have specialties along with developmental orientations. Including, you are looking at system along with aspire to certainly be a system supervisor, you possibly can decide on certifications for Microsoft MCP, MCSE, along with Novells CNE, MCNE, and Suns SCJP, etcetera; Should you be accomplished at data source, you possibly can make examinations for qualifications connected with data source, including Microsoft MCDBA as well as Oracle, Sybase, IBM. Furthermore, in addition there are several authentications in regards to the figure along with photograph, people today, who are considering graphic design, webpage generating et cetera, may possibly take into consideration them.
Q91. Refer to the exhibit.
A problem with network connectivity has been observed. It is suspected that the cable connected to switch port
Fa0/9 on Switch1 is disconnected. What would be an effect of this cable being disconnected?
A. Host B would not be able to access the server in VLAN9 until the cable is reconnected.
B. Communication between VLAN3 and the other VLANs would be disabled.
C. The transfer of files from Host B to the server in VLAN9 would be significantly slower.
D. For less than a minute, Host B would not be able to access the server in VLAN9. Then normal network function would resume.
Q92. What is the purpose of the switchport command?
Switch(config-if)# switchport port-security maximum 1 Switch(config-if)# switchport port-security mac-address 0018.DE8B.4BF8
A. It ensures that only the device with the MAC address 0018.DE8B.4BF8 will be able to connect to the port that is being configured.
B. It informs the switch that traffic destined for MAC address 0018.DE8B.4BF8 should only be sent to the port that is being configured.
C. It will act like an access list and the port will filter packets that have a source or destination MAC of 0018.DE8B.4BF8.
D. The switch will shut down the port of any traffic with source MAC address of 0018.DE8B.4BF8.
Q93. Which IP addresses are valid for hosts belonging to the 10.1.160.0/20 subnet? (Choose three.)
Q94. The ip helper-address command does what?
A. assigns an IP address to a host
B. resolves an IP address from a DNS server
C. relays a DHCP request across networks
D. resolves an IP address overlapping issue
Q95. Refer to the exhibit.
The host in Kiev sends a request for an HTML document to the server in Minsk. What will be the source IP address of the packet as it leaves the Kiev router?
Q96. How does a switch differ from a hub?
A. A switch does not induce any latency into the frame transfer time.
B. A switch tracks MAC addresses of directly-connected devices.
C. A switch operates at a lower, more efficient layer of the OSI model.
D. A switch decreases the number of broadcast domains.
E. A switch decreases the number of collision domains.
Q97. Refer to the exhibit.
The two connected ports on the switch are not turning orange or green. What would be the most effective steps to troubleshoot this physical layer problem? (Choose three.)
A. Ensure that the Ethernet encapsulations match on the interconnected router and switch ports.
B. Ensure that cables A and B are straight-through cables.
C. Ensure cable A is plugged into a trunk port.
D. Ensure the switch has power.
E. Reboot all of the devices.
F. Reseat all cables.
Q98. Which one of the following IP addresses is the last valid host in the subnet using mask 255.255.255.224?
Q99. What command sequence will configure a router to run OSPF and add network 10.1.1.0 /24 to area 0?
A. router ospf area 0 network 10.1.1.0 255.255.255.0 area 0
B. router ospf network 10.1.1.0 0.0.0.255
C. router ospf 1 network 10.1.1.0 0.0.0.255 area 0
D. router ospf area 0 network 10.1.1.0 0.0.0.255 area 0
E. router ospf network 10.1.1.0 255.255.255.0 area 0
F. router ospf 1 network 10.1.1.0 0.0.0.255
Q100. The following commands are entered on the router:
Burbank(config)# enable secret fortress Burbank(config)# line con 0 Burbank(config-line)# login Burbank(config-line)# password n0way1n Burbank(config-line)# exit Burbank(config)# service password-encryption
What is the purpose of the last command entered?
A. to require the user to enter an encrypted password during the login process
B. to prevent the vty, console, and enable passwords from being displayed in plain text in the configuration files
C. to encrypt the enable secret password
D. to provide login encryption services between hosts attached to the router
To know more about the 100-101, click here.