200-101 Guide

The Only Tip You Need: icnd2 questions

Cisco Cisco exam demos contain reliable and valuable questions & answers which will offer an individual abundant main factors to pass the exam on your initial try. They will cover every one of the topics in the Cisco exam. Passing the exam will be a new breeze for you. Among the obvious and distinct features of our Cisco 200-101 exam dumps can be that this guarantees your own success in the real assessment room. Get certified with full confidence and hunt for a very good job. Many of us also offer you the entire refund policy. If you don?¡¥t pass the Cisco Cisco 200-101 certification exam after using our exam demos with the first attempt, you need to simply email us your failed transcript, and you will get the money back shortly.

2021 Oct ccna vs icnd1 and icnd2:

Q51. Which two states are the port states when RSTP has converged? (Choose two.) 

A. discarding 

B. listening 

C. learning 

D. forwarding 

E. disabled 

Answer: AD 


Q52. Refer to the exhibit. 


Assuming that the entire network topology is shown, what is the operational status of the interfaces of R2 as indicated by the command output shown? 

A. One interface has a problem. 

B. Two interfaces have problems. 

C. The interfaces are functioning correctly. 

D. The operational status of the interfaces cannot be determined from the output shown. 

Answer: C 


Q53. Which command is used to display the collection of OSPF link states? 

A. show ip ospf link-state 

B. show ip ospf lsa database 

C. show ip ospf neighbors 

D. show ip ospf database 

Answer: D 


Q54. Refer to the exhibit. 


A network associate has configured OSPF with the command: 

City(config-router)# network 192.168.12.64 0.0.0.63 area 0 

After completing the configuration, the associate discovers that not all the interfaces are participating in OSPF. Which three of the interfaces shown in the exhibit will participate in OSPF according to this configuration statement? (Choose three.) 

A. FastEthernet0 /0 

B. FastEthernet0 /1 

C. Serial0/0 

D. Serial0/1.102 

E. Serial0/1.103 

F. Serial0/1.104 

Answer: BCD 


Q55. Which two statements about using the CHAP authentication mechanism in a PPP link are true? (Choose two.) 

A. CHAP uses a two-way handshake. 

B. CHAP uses a three-way handshake. 

C. CHAP authentication periodically occurs after link establishment. 

D. CHAP authentication passwords are sent in plaintext. 

E. CHAP authentication is performed only upon link establishment. 

F. CHAP has no protection from playback attacks. 

Answer: BC 


200-101 braindumps

Renew ccna icnd2 book:

Q56. The command show frame-relay map gives the following output: 

Serial 0 (up): ip 192.168.151.4 dlci 122, dynamic, broadcast, status defined, active 

Which statements represent what is shown?(Choose three.) 

A. 192.168.151.4 represents the IP address of the remote router 

B. 192.168.151.4 represents the IP address of the local serial interface 

C. DLCI 122 represents the interface of the remote serial interface 

D. DLCI 122 represents the local number used to connect to the remote address 

E. broadcast indicates that a dynamic routing protocol such as RIP v1 can send packets across this PVC 

F. active indicates that the ARP process is working 

Answer: ADE 


Q57. Refer to the exhibit. 


Based on the exhibited routing table, how will packets from a host within the 192.168.10.192/26 LAN be forwarded to 192.168.10.1? 

A. The router will forward packets from R3 to R2 to R1. 

B. The router will forward packets from R3 to R1 to R2. 

C. The router will forward packets from R3 to R2 to R1 AND from R3 to R1. 

D. The router will forward packets from R3 to R1. 

Answer: C 


Q58. Which two statements describe the process identifier that is used in the command to configure OSPF on a router? (Choose two.) 

Router(config)# router ospf 1 

A. All OSPF routers in an area must have the same process ID. 

B. Only one process number can be used on the same router. 

C. Different process identifiers can be used to run multiple OSPF processes 

D. The process number can be any number from 1 to 65,535. 

E. Hello packets are sent to each neighbor to determine the processor identifier. 

Answer: CD 


Q59. Which commands are required to properly configure a router to run OSPF and to add network 192.168.16.0/24 to OSPF area 0? (Choose two.) 

A. Router(config)# router ospf 0 

B. Router(config)# router ospf 1 

C. Router(config)# router ospf area 0 

D. Router(config-router)# network 192.168.16.0 0.0.0.255 0 

E. Router(config-router)# network 192.168.16.0 0.0.0.255 area 0 

F. Router(config-router)# network 192.168.16.0 255.255.255.0 area 0 

Answer: BE 


Q60. Which Layer 2 protocol encapsulation type supports synchronous and asynchronous circuits and has built-in security mechanisms? 

A. HDLC 

B. PPP 

C. X.25 

D. Frame Relay 

Answer: B 


To know more about the 200-101, click here.

Tagged as : Cisco 200-101 Dumps, Download 200-101 pdf, 200-101 VCE, 200-101 pass4sure, examcollection 200-101