200-120 Guide

Why You Need To cisco ccna 200-120?

It is impossible to pass Cisco 200-120 exam without any help in the short term. Come to Exambible soon and find the most advanced, correct and guaranteed Cisco 200-120 practice questions. You will get a surprising result by our Regenerate CCNA Cisco Certified Network Associate CCNA (803) practice guides.

2021 Nov nikon 24-120 vs 28-200:

Q141. - (Topic 4) 

What is the default maximum number of equal-cost paths that can be placed into the routing table of a Cisco OSPF router? 

A. 2 

B. 8 

C. 16 

D. unlimited 

Answer:


Q142. - (Topic 1) 

Refer to the exhibit. 

Based on the information given, which switch will be elected root bridge and why? 

A. Switch A, because it has the lowest MAC address 

B. Switch A, because it is the most centrally located switch 

C. Switch B, because it has the highest MAC address 

D. Switch C, because it is the most centrally located switch 

E. Switch C, because it has the lowest priority 

F. Switch D, because it has the highest priority 

Answer:


Q143. - (Topic 4) 

Refer to the exhibit. 

What is the reason that the interface status is "administratively down, line protocol down"? 

A. There is no encapsulation type configured. 

B. There is a mismatch in encapsulation types. 

C. The interface is not receiving any keepalives. 

D. The interface has been configured with the shutdown command. 

E. The interface needs to be configured as a DTE device. 

F. The wrong type of cable is connected to the interface. 

Answer:


Q144. CORRECT TEXT - (Topic 7) 

Central Florida Widgets recently installed a new router in their office. Complete the network installation by performing the initial router configurations and configuring R1PV2 routing using the router command line interface (CLI) on the RC. 

Configure the router per the following requirements: 

Name of the router is R2 

Enable. secret password is cisco 

The password to access user EXEC mode using the console is cisco2 

The password to allow telnet access to the router is cisco3 

IPV4 addresses mast be configured as follows: 

Ethernet network 209.165.201.0/27 - router has fourth assignable host address in subnet 

Serial network is 192.0.2.176/28 - router has last assignable host address in the subnet. 

Interfaces should be enabled. 

Router protocol is RIPV2 

Attention: 

In practical examinations, please note the following, the actual information will prevail. 

1. Name or the router is xxx 

2. EnablE. secret password is xxx 

3. Password In access user EXEC mode using the console is xxx 

4. The password to allow telnet access to the router is xxx 

5. IP information 

Answer: Router>enable Router#config terminal Router(config)#hostname R2 R2(config)#enable secret Cisco 1 R2(config)#line console 0 R2(config-line)#password Cisco 2 R2(config-line)#exit R2(config)#line vty 0 4 R2(config-line)#password Cisco 3 R2(config-line)#login R2(config-line)#exit R2(config)#interface faO/0 R2(config-if)#ip address 209.165.201.4 255.255.255.224 R2(config)#interface s0/0/0 R2(config-if)#ip address 192.0.2.190 255.255.255.240 R2(config-if)#no shutdown R2(config-if)#exit R2(config)#router rip R2(config-router)#version 2 R2(config-router)#network 209.165.201.0 R2(config-router)#network 192.0.2.176 R2(config-router)#end R2#copy run start 


Q145. - (Topic 7) 

What Netflow component can be applied to an interface to track IPv4 traffic? 

A. flow monitor 

B. flow record 

C. flow sampler 

D. flow exporter 

Answer:


Renew ccna routing and switching 200-120:

Q146. - (Topic 8) 

Which Layer 2 protocol encapsulation type supports synchronous and asynchronous circuits and has built-in security mechanisms? 

A. HDLC 

B. PPP 

C. X.25 

D. Frame Relay 

Answer:


Q147. - (Topic 4) 

Refer to the exhibit. 

Based on the exhibited routing table, how will packets from a host within the 192.168.10.192/26 LAN be forwarded to 192.168.10.1? 

A. The router will forward packets from R3 to R2 to R1. 

B. The router will forward packets from R3 to R1 to R2. 

C. The router will forward packets from R3 to R2 to R1 AND from R3 to R1. 

D. The router will forward packets from R3 to R1. 

Answer:


Q148. - (Topic 5) 

Which three are the components of SNMP? (Choose three) 

A. MIB 

B. SNMP Manager 

C. SysLog Server 

D. SNMP Agent 

E. Set 

Answer: A,B,D 


Q149. - (Topic 4) 

Which parameter would you tune to affect the selection of a static route as a backup, when a dynamic protocol is also being used? 

A. hop count 

B. administrative distance 

C. link bandwidth 

D. link delay 

E. link cost 

Answer:


Q150. - (Topic 9) 

Which three characteristics are representative of a link-state routing protocol? (Choose three.) 

A. provides common view of entire topology 

B. exchanges routing tables with neighbors 

C. calculates shortest path 

D. utilizes event-triggered updates 

E. utilizes frequent periodic updates 

Answer: A,C,D 


To know more about the 200-120, click here.

Tagged as : Cisco 200-120 Dumps, Download 200-120 pdf, 200-120 VCE, 200-120 pass4sure, examcollection 200-120