200-120 Guide

An Expert interview about cisco ccna 200-120

Want to know Pass4sure 200-120 Exam practice test features? Want to lear more about Cisco CCNA Cisco Certified Network Associate CCNA (803) certification experience? Study Approved Cisco 200-120 answers to Latest 200-120 questions at Pass4sure. Gat a success with an absolute guarantee to pass Cisco 200-120 (CCNA Cisco Certified Network Associate CCNA (803)) test on your first attempt.

2021 Dec ccna dumps for 200-120:

Q131. - (Topic 1) 

Which three statements accurately describe Layer 2 Ethernet switches? (Choose three.) 

A. Spanning Tree Protocol allows switches to automatically share VLAN information. 

B. Establishing VLANs increases the number of broadcast domains. 

C. Switches that are configured with VLANs make forwarding decisions based on both Layer 2 and Layer 3 address information. 

D. Microsegmentation decreases the number of collisions on the network. 

E. In a properly functioning network with redundant switched paths, each switched segment will contain one root bridge with all its ports in the forwarding state. All other switches in that broadcast domain will have only one root port. 

F. If a switch receives a frame for an unknown destination, it uses ARP to resolve the address. 

Answer: B,D,E 


Q132. - (Topic 5) 

A network administrator enters the following command on a router: logging trap 3. What are three message types that will be sent to the Syslog server? (Choose three.) 

A. informational 

B. emergency 

C. warning 

D. critical 

E. debug 

F. error 

Answer: B,D,F 


Q133. - (Topic 4) 

Refer to the exhibit. 

If the router Cisco returns the given output and has not had its router ID set manually, what 

value will OSPF use as its router ID? 

A. 192.168.1.1 

B. 172.16.1.1 

C. 1.1.1.1 

D. 2.2.2.2 

Answer:


Q134. - (Topic 9) 

Which command can you enter to configure a local username with an encrypted password and EXEC mode user privileges? 

A. Router(config)#username jdone privilege 1 password 7 08314D5D1A48 

B. Router(config)#username jdone privilege 1 password 7 PASSWORD1 

C. Router(config)#username jdone privilege 15 password 0 08314D5D1A48 

D. Router(config)#username jdone privilege 15 password 0 PASSWORD1 

Answer:


Q135. - (Topic 4) 

Refer to the exhibit. 

Why is flash memory erased prior to upgrading the IOS image from the TFTP server? 

A. The router cannot verify that the Cisco IOS image currently in flash is valid. 

B. Flash memory on Cisco routers can contain only a single IOS image. 

C. Erasing current flash content is requested during the copy dialog. 

D. In order for the router to use the new image as the default, it must be the only IOS image in flash. 

Answer:


Latest free ccna 200-120 dumps:

Q136. - (Topic 3) 

Which option is a valid IPv6 address? 

A. 2001:0000:130F::099a::12a 

B. 2002:7654:A1AD:61:81AF:CCC1 

C. FEC0:ABCD:WXYZ:0067::2A4 

D. 2004:1:25A4:886F::1 

Answer:


Q137. - (Topic 4) 

What two things will a router do when running a distance vector routing protocol? (Choose two.) 

A. Send periodic updates regardless of topology changes. 

B. Send entire routing table to all routers in the routing domain. 

C. Use the shortest-path algorithm to the determine best path. 

D. Update the routing table based on updates from their neighbors. 

E. Maintain the topology of the entire network in its database. 

Answer: A,D 


Q138. - (Topic 7) 

Refer to the exhibit. 

HostA cannot ping HostB. Assuming routing is properly configured, what is the cause of this problem? 

A. HostA is not on the same subnet as its default gateway. 

B. The address of SwitchA is a subnet address. 

C. The Fa0/0 interface on RouterA is on a subnet that can't be used. 

D. The serial interfaces of the routers are not on the same subnet. 

E. The Fa0/0 interface on RouterB is using a broadcast address. 

Answer:


Q139. - (Topic 3) 

Refer to the exhibit. 

What is the most appropriate summarization for these routes? 

A. 10.0.0.0 /21 

B. 10.0.0.0 /22 

C. 10.0.0.0 /23 

D. 10.0.0.0 /24 

Answer:


Q140. - (Topic 9) 

Which command can you execute to set the user inactivity timer to 10 seconds? 

A. SW1(config-line)#exec-timeout 0 10 

B. SW1(config-line)#exec-timeout 10 

C. SW1(config-line)#absolute-timeout 0 10 

D. SW1(config-line)#absolute-timeout 10 

Answer:


To know more about the 200-120, click here.

Tagged as : Cisco 200-120 Dumps, Download 200-120 pdf, 200-120 VCE, 200-120 pass4sure, examcollection 200-120