200-401 Guide

The Secret of ipa-client-install http response code is 401 not 200

We provide free updated Cisco 200-401 practice components for 120 days in the date of purchasing. You should examine the most recent Cisco 200-401 exam dumps at Ucertify. As well as download the Cisco 200-401 practice questions. Each of our study guide will help you to make for the Cisco Cisco 200-401 coherently which usually guarantee your current success in the real exam. Please sense free to contact us if you have got any questions. Each of our customer service are offered by anytime.

2021 Dec expected status code in (200-299) got 401:

Q11. - (Topic 4) 

At which Layer would you check for spanning tree loops? 

A. Layer 1 

B. Layer 2 

C. Layer 3 

D. Layer 4 

Answer:


Q12. - (Topic 5) 

With a Cisco IE 2000 switch, what does a power status LED indicate when it is solid green? 

A. Power is present on the associated circuit and the system is operating normally. 

B. Power is present on the associated circuit, but there is no correlation to whether the system is operating normally. 

C. The system is operating normally, but power is not necessarily present on the associated circuit. 

D. Power is not present on the associated circuit and the power supply alarm is configured. 

E. The power status LED does not show solid green. 

Answer:


Q13. - (Topic 2) 

Given a ring topology, which loop prevention mechanism provides the fastest reconvergence time after a link failure? 

A. Rapid Per-VLAN Spanning Tree Protocol 

B. Resilient Ethernet Protocol 

C. Multiple Spanning Tree Protocol 

D. Spanning Tree Protocol 

Answer:


Q14. - (Topic 1) 

Exhibit: Refer to the exhibit..Which port should a PLC with IP address 192.168.3.65 be plugged into in order to communicate to the rest of the network? 

A. FastEthernet1/1 

B. FastEthernet1/2 

C. FastEthernet1/3 

D. FastEthernet1/4 

E. FastEthernet1/5 

Answer:


Q15. - (Topic 3) 

Which characteristic causes multimode fiber-optic cable to differ from single mode? 

A. by allowing multiple network services in the same cable 

B. shorter maximum network segment length for a given bandwidth 

C. a wider variety of available connector types 

D. use outdoors as well as indoors 

Answer:


Far out clicktronic hc 401-200:

Q16. - (Topic 1) 

Exhibit: Refer to the exhibit. What are three traffic and interconnection requirements for the devices in the exhibit? (Choose three.) 

A. The EtherNet/IP drive connections are in a high-voltage area and need protection from electromagnetic noise, so.shielded cable that is rated for 600 V.is advised. 

B. EtherNet/IP devices such as the controller, drive, VoIP phone, and IP camera should be in the same VLAN. 

C. CIP traffic has the highest bandwidth requirement so it needs the highest QoS setting. 

D. EtherNet/IP drive traffic has high sensitivity to random drops, latency, and jitter. 

E. Real-time motion control and VoIP traffic can share the same VLAN with the proper QoS setting. 

F. IEEE1588 and PTP are important for ensuring real-time synchronization. 

Answer: A,D,F 


Q17. - (Topic 5) 

Which three pieces of information must be maintained for all stakeholders as part of the change management process? (Choose three.) 

A. the location of the person who applied the change 

B. the date and time that the change was applied and on which device 

C. the original change request form that indicates why the change is necessary 

D. the size of the change (in bytes) 

E. a description of the actual change itself.(configuration, program code, and so on) 

F. the names of the current members of the change advisory board 

G. the industrial protocol that is used 

Answer: B,C,E 


Q18. - (Topic 4) 

Exhibit: 

Refer to the exhibit. The output that is shown is generated at an industrial switch. Which three statements are true? (Choose three.) 

A. All ports will be in a state of discarding, learning, or forwarding. 

B. Thirty VLANs have been configured on this switch. 

C. The bridge priority is lower than the default value for spanning tree. 

D. All interfaces that are shown are on shared media. 

E. All designated ports are in a forwarding state. 

F. This switch must be the root bridge for all VLANs on this switch. 

Answer: A,C,E 


Q19. - (Topic 5) 

Which two commands can help you to determine what image is running on your industrial switch? (Choose two.) 

A. show version 

B. show spanning-tree 

C. show interface-switch 

D. show interfaces gigabitEthernet x/y switchport 

E. show license 

Answer: A,E 


Q20. - (Topic 5) 

How does the optical time domain reflectometer use "backscattered" light to make measurements? 

A. It uses pulses to locate and test for sheath faults, damaged conductors, loose connectors, splices, bridge taps, split pairs, and other problems. 

B. It performs wiremapping to measure that all pins are correctly connected. 

C. It correlates the returned light pulses with a location in the fiber. 

D. It measures light-pulse width to measure that all pins are correctly connected. 

Answer:


To know more about the 200-401, click here.

Tagged as : Cisco 200-401 Dumps, Download 200-401 pdf, 200-401 VCE, 200-401 pass4sure, examcollection 200-401