200-601 Guide

Finding Up to the minute 200-601 discount pack

Cause all that matters here is passing the Cisco 200-601 exam. Cause all that you need is a high score of 200-601 Managing Industrial Networking for Manufacturing with Cisco Technologies exam. The only one thing you need to do is downloading Examcollection 200-601 exam study guides now. We will not let you down with our money-back guarantee.

2021 Nov 200-601 test preparation

Q41. What can be done to increase the security in depth in an industrial zone? 

A. Add additional disk storage to the IDS server 

B. Add specific SCADA signatures to the IDS server 

C. Create a high availability solution for the IDS server 

D. Place a 'data diode' in front of the IDS server 

Answer:


Q42. Refer to the exhibit. 

A new device, PanelView, has been added to the network. See the table for device details: 

All devices are able to ping their default gateway and all other devices except PanelView. 

PanelView can only ping its default gateway. 

After the administrator has done some investigation they have discovered the following 

information: 

L3SW1# show run interface 

interface Vlan1 no ip address shutdown ! interface Vlan191 ip address 10.10.27.125 255.255.255.192 ip helper-address 165.28.96.96 ip helper-address 165.28.32.235 no ip redirects standby 191 ip 10.10.27.126 standby 191 priority 120 standby 191 preempt delay minimum 90 no ip route-cache ! interface Vlan398 ip vrf forwarding mosaic ip address 10.15.153.203 255.255.255.0 ip helper-address 10.15.154.252 ip helper-address 10.1.0.252 standby 98 ip 10.15.153.202 standby 98 priority 120 standby 98 preempt delay minimum 90 ! interface Vlan399 ip vrf forwarding mosaic ip address 10.15.154.203 255.255.255.0 

ip helper-address 10.1.0.252 

ip helper-address 10.1.1.252 

standby 99 ip 10.15.154.254 

standby 99 priority 120 

standby 99 preempt delay minimum 90 

L3SW1# show ip route connected 10.0.0.0/8 is variably subnetted, 1149 subnets, 17 masks 

C.10.10.27.64/26 is directly connected, Vlan191 

C.10.10.31.254/32 is directly connected, Loopback1 

What is preventing PanelView from pinging the other endpoints in the network? 

A. Routing isn't enabled on L3SW1 for.SVI 398 and.SVI 399 

B. SVI 191 is in a different routing instance than.SVI 398 and SVI 399 

C. Firewall1 is blocking pings from PanelView to the other endpoints 

D. An access list on L3SW1 is blocking pings from PanelView to the other endpoints 

Answer:


Q43. What security component can be deployed to increase the defense in depth and specifically can be positioned against 'man-in-the-middle' attack? 

A. Deploy 802.1AE 

B. Deploy 802.1X 

C. Deploy 802.1Q 

D. Deploy 802.1AX 

Answer:


Improved 200-601 rapidshare:

Q44. Refer to the exhibit. 

L3SW1 has a spanning-tree priority of 8192 set on VLANs 1, 300, and 301, and these VLANs are configured on and trunked between all switches. Executing the command show spanning-tree blockedports on L2SW5 results in: 

L2SW5# show spanning-tree blockedports 

Name.Blocked Interfaces List VLAN0001.Gi1/1 

VLAN0300.Gi1/1 

VLAN0301.Gi1/1 

An additional VLAN, VLAN302, is defined on all switches and trunked between them. VLAN302 access ports are set up on each of the switches and PLC#1, I/O#1, and the PanelView are attached. You expect the new VLAN to be listed as blocked on interface GigabitEthernet1/1 of L2SW5 but it is not. The three new devices are able to communicate with each other. 

After executing the same command on all switches you see this output on L2SW4: 

L2SW4# show spanning-tree blockedports 

Name.Blocked Interfaces List 

VLAN0001.Gi1/2 

VLAN0300.Gi1/2 

VLAN0301.Gi1/2 

Why is VLAN302 forwarding on L2SW5 interface GigabitEthernet 1/1 and L2SW4 interface GigabitEthernet 1/1 and 1/2? 

A. VLAN302 is not configured in the VLAN database on L2SW5 

B. VLAN302 is not in the allowed list on the L2SW5 interface GigabitEthernet1/1 trunk 

C. L2SW4 is the spanning tree root for VLAN 302 

D. The FO3 fiber-optic cable between L2SW4 and L2SW5.is damaged 

Answer:


Q45. You are making changes to a Stratix 5700 using an Add On Profile (AOP) and a controller which is on-line with RSLogix5000. When do the changes you have made get published to the switch? 

A. While online in RSLogix 5000 software the changes made in the AOP are pushed to the switch after pressing the Set button. 

B. All of the changes are automatically pushed to the switch. 

C. Changes to the AOP can only be made from the switch, not in RSLogix 5000. 

D. RSLogix 5000 will push the changes in the AOP to the Stratix 5700 when you right click on the switch, and choose download to switch 

Answer:


Q46. Refer to the exhibit. 

The control system depicted in the exhibit uses VLAN 300 for all of its device ports and PVST is enabled on each switch to switch connection. L2SW4 was inserted between L2SW3 and L2SW5. Links FO2 and FO3 were added and FO1 was disconnected. 

Prior to the installation of L2SW4, PanelView was able to communicate with PLC#1. After the change, PLC#1 and PanelView are still able to communicate but neither PLC#1 or PanelView are able to communicate with I/O #1. 

L2SW4# show run.interfaces FastEthernet 1/1 

description I/O#1 

switchport access vlan 300 

switchport mode access 

spanning-tree portfast 

spanning-tree bpduguard enable 

L2SW4# show interfaces trunk 

Port.Mode.Encapsulation.Status.Native vlan Gi1/1.on.

802.1q.trunking.1 Gi1/2.on.802.1q.trunking.1 Port.Vlans allowed on trunk Gi1/1.1,3-9, 301-305,400 Gi1/2 1,3-9, 301-305,400 Port.Vlans allowed and active in management domain Gi1/1.1,3-9, 301-305,400 Gi1/2.1,3-9, 301-305,400 Port.Vlans in spanning tree forwarding state and not pruned Gi1/1.1,3-9, 301-305,400 Gi1/2.

Based on the output from the switch, what is preventing I/O#1 from communicating with PLC#1 and PanelView? 

A. Interface FastEthernet 1/1 on LWSW4 should be configured as a trunk port 

B. The trunks connecting L2SW4 to L2SW3 and L2SW5 have the wrong encapsulation type 

C. The trunks connecting L2SW4 to L2SW3 and L2SW5 don't allow VLAN 300 traffic 

D. BPDU guard has error-disabled interface FastEthernet 1/1 on LWSW4 

Answer:


To know more about the 200-601, click here.

Tagged as : Cisco 200-601 Dumps, Download 200-601 pdf, 200-601 VCE, 200-601 pass4sure, examcollection 200-601