200-601 Guide

Shortcuts To 200-601(31 to 40)

What can you get along with your purchase of the Cisco 200-601 items are because follows: 1. A new study guidebook for Cisco Cisco examination engine and Pdf. 2. A new preview of Cisco 200-601 true exam questions. 3. A good overview of Cisco 200-601 on the web training study course. 4. Correct answers to the 200-601 practice questions. Throw away the thicker Cisco 200-601 books and act now and download the Cisco Cisco 200-601 today! With our restricted but important Cisco Cisco certification exam questions and answers to adopt the 200-601 genuine exam, you will obtain a high indicate which assures the success.

2021 Dec 200-601 test

Q31. Cisco Industrial Ethernet switches are capable of sending alarm messages to ProfiNET management stations using the ProfiNET-IO protocol. Which four are alarms that can be configured for an interface? (Choose four) 

A. Port Not Forwarding 

B. Port Not Operating 

C. Port LLDP Disabled 

D. Port QoS Disabled 

E. Port Duplex Mismatch 

F. Port FCS Errors Exceeded Threshold 

G. Port CRC Errors Exceeded Threshold 

H. Port Link Fault 

Answer: A,B,F,H 


Q32. Refer to the exhibit. 

All of the vlans listed in the routing table below are trunked using 802.1q and are active on all switches. PLC1, PLC2, and PLC3 each has IP address 192.168.0.1/24 and are connected to ports configured for vlan 50. L2SW1, L2SW2, and L2SW3 are not using vlan trunking for vlan 50. 

L3SW1 has following routing table:

 10.0.0.0/8 is variably subnetted, 12 subnets, 2 masks C.10.3.138.0/23 is directly connected, Vlan307 C.10.3.136.0/23 is directly connected, Vlan306 C.10.15.153.0/24 is directly connected, Vlan398 C.10.3.142.0/23 is directly connected, Vlan309 C.10.3.140.0/23 is directly connected, Vlan308 C.10.3.186.0/23 is directly connected, Vlan293 C.10.15.154.0/24 is directly connected, Vlan399 C.10.3.184.0/23 is directly connected, Vlan292 C.10.3.190.0/23 is directly connected, Vlan295 C.10.3.188.0/23 is directly connected, Vlan294 

C.10.3.182.0/23 is directly connected, Vlan291 

C.10.3.180.0/23 is directly connected, Vlan290 

PLC1, PLC2, and PLC3 cannot be reconfigured. What can be done to be able to simultaneously communicate with PLC1, PLC2, and PLC3? 

A. Enable NAT on L3SW1 

B. Enable NAT on L2SW1 – L2SW3 

C. Enable NAT on L2SW4 

D. Add vlan 50 to L2SW4 and assign.the administrator's.an IP address on 192.168.0.0/24 network 

Answer:


Q33. Which scenario represents the correct configuration to support the SSIDs of this autonomous access point? 

A. 

B. 

C. 

D. 

Answer:


Q34. Which is an issue with running CIP Motion on a REP network and identifies an alternate resiliency protocol that works for CIP Motion? 

A. CIP Motion requires a star topology which is not supported by REP. DLR is a suitable resiliency protocol for CIP motion. 

B. REP convergence is not fast enough. DLR is a suitable resiliency protocol for CIP motion. 

C. CIP Motion requires a star topology which is not supported by REP. RPVST+.is a suitable resiliency protocol for CIP motion. 

D. REP convergence is not fast enough. RPVST+.is a suitable resiliency protocol for CIP motion. 

Answer:


Q35. If.the Link Fault alarm is connected to the minor relay and the FCS Bit Error Rate alarm is connected to the major relay, which commands will create an alarm profile called GigE with the alarms correctly mapped to the minor and major relays? 

A. Switch(config)#alarm profile GigE Switch(config-alarm-prof)#alarm 1 4 Switch(config-alarm-prof)#relay major 4 Switch(config-alarm-prof)#relay minor 1 

B. Switch(config)#alarm profile GigE Switch(config-alarm-prof)#alarm 1 3 Switch(config-alarm-prof)#relay major 3 Switch(config-alarm-prof)#relay minor 1 

C. Switch(config)#alarm profile GigE Switch(config-alarm-prof)#alarm 1 3 Switch(config-alarm-prof)#relay major 1 Switch(config-alarm-prof)#relay minor 3 

D. Switch(config)#alarm profile GigE Switch(config-alarm-prof)#alarm 1 4 Switch(config-alarm-prof)#relay major 1 Switch(config-alarm-prof)#relay minor 4 

Answer:


Far out 200-601 rapidshare:

Q36. What are three Cisco best practices for running I/O control traffic in a wireless environment? (Choose three) 

A. 3200 packets per second and 20% bandwidth for HMI and maintenance traffic. 

B. 2200 packets per second and 20% bandwidth for HMI and maintenance traffic 

C. I/O control traffic can be run on 2.4 or 5 GHZ channels 

D. I/O control traffic should be run on 5GHZ channels only 

E. Standard I/O RPIs less than 20ms are not practical for wireless media because the maximum latency and jitter become comparable or greater than the RPI 

F. Standard I/O RPIs less than 10ms are not practical for wireless media because the maximum latency and jitter become comparable or greater than the RPI 

Answer: B,D,F 


Q37. A ProfiNET management system operator is unable to add a ProfiNET Conformance Class B device to a SIMATIC management station. The device is connected to interface 

FastEthernet1/3. Based on the provided CLI output, which statement is correct? 

switch#show profinet lldp Fa1/1.port-003-00000 On Fa1/2.port-004-00000 On Fa1/3.port-005-00000 Off Fa1/4.port-006-00000 Off Fa1/5.port-007-00000 On Fa1/6.port-008-00000 Off Fa1/7.port-009-00000 On Fa1/8.port-010-00000 Off 

A. LLDP has been disabled on this switch 

B. The connected device is not sending LLDP packets with ProfiNET extensions 

C. The port label needs to be changed on interface FastEthernet 1/3 to "port-003-00000" 

D. ProfiNET is disabled on this switch 

Answer:


Q38. Refer to the exhibit. 

Network Faceplates have not been installed on the HMI and so you need to map a network based on information available from RSLinx. Which most accurately represents the network configuration? 

A. 

B. 

C. 

D. 

Answer:


Q39. Which three network mechanisms can be used for securely segmenting an industrial network? (Choose three) 

A. VLANs 

B. OSPF 

C. REP 

D. VRFs 

E. Firewalls 

F. Spanning-tree 

Answer: A,D,E 


Q40. Which describes the relationship between a workgroup bridge? 

A. Wired clients of a workgroup bridge can communicate, through the workgroup bridge, with wireless clients of an autonomous or a controller-based access point 

B. Wireless clients of a controller-based AP can communicate, through the workgroup bridge, with wireless clients of an autonomous access point 

C. Wireless clients of an autonomous access point can communicate with wired clients of a workgroup bridge, but Wireless clients of a controller-based access point cannot communicate with wired clients of a workgroup bridge 

D. Wireless clients of a controller-based access point can communicate with wired clients of a workgroup bridge, but Wireless clients of an autonomous access point cannot communicate with wired clients of a workgroup bridge 

Answer:


To know more about the 200-601, click here.

Tagged as : Cisco 200-601 Dumps, Download 200-601 pdf, 200-601 VCE, 200-601 pass4sure, examcollection 200-601