Finding Improved 300-360 class

Your success in Cisco 300-360 is our sole target and we develop all our 300-360 braindumps in a way that facilitates the attainment of this target. Not only is our 300-360 study material the best you can find, it is also the most detailed and the most updated. 300-360 Practice Exams for Cisco CCNP Wireless 300-360 are written to the highest standards of technical accuracy.

Q1. Refer to the exhibit.

While testing the post-deployment WLAN network, you discover that an AP has been placed in a difficult area.

The AP cannot be moved easily because of various requirements. The client performance of various Apple and Microsoft operating system-based products does not meet expectations. Which two options can help mitigate the performance issue? (Choose two.)

A. Add additional APs.

B. Increase the AP power level to maximum.

C. Rotate the AP 90 degrees to change antenna polarity.

D. Replace the AP with an AP and external antenna.

E. Change the AP location to one that is less RF hostile.

Answer: A,D

Q2. A customer is deploying a mesh outdoor wireless network based on FCC standards where spectrum analysis shows significant radar energy propagating throughout the coverage area from a local weather station. Which channel must be excluded from the access points RRM calculation to avoid network disruption due to weather radar activity?

A. 132

B. 44

C. 11

D. 36

Answer: A

Explanation:

Weather radars operate within the 5600- to 5650-MHz band, which means that channels 124 and 128 might be affected, but also channels 120 and 132 might suffer from weather radar activity.

Reference: http://www.cisco.com/c/en/us/td/docs/wireless/technology/mesh/7-3/design/guide/Mesh/ Mesh_chapter_0111.html

Q3. A network engineer is preparing for an office site survey with a height of 2.5 meters. Which three components are recommended to complete the survey? (Choose three.)

A. Use APs with external antennas.

B. Use DoS attack on APs while measuring the throughput.

C. Use APs with built-in antennas.

D. Use a battery pack to power APs.

E. Use a drawing of the office space to draw AP and client placements.

F. Use APs with directional antennas.

Answer: C,D,E

Q4. An engineer receives a digital image scanned from the floor plans of a facility to be surveyed for wireless survey and imported it into Air Magnet Pro. However, the document contains no scale. Which action can the engineer take to most accurately calibrate the size of the floor plan in Air Magnet?

A. Mark the length of a hallway, then count the ceiling tiles, multiply that number by 2 and enter that value.

B. Zoom in and mark across a hallway, then count the floor tiles across that hallway and enter that value.

C. Zoom in and mark a doorway, then size it at 3 feet because most doorways are 36 inches.

D. Mark the entire longest dimension of the floorplan, then use Google Earth to measure the correspondingoutside dimension and enter that value.

Answer: D

Q5. An engineer is assigned to replace an older data-grade autonomous wireless network with a Cisco controllerbased wireless network to meet Voice over WLAN needs. The customer also wants all existing cable infrastructure to be reused and no new cable be specified. How should the engineer respond to the customer’s requirements?

A. Implement the wireless network with the restraints and decrease the TPC neighbor threshold to increase Txpower to provide overlapping cell coverage at sufficient SNR to provide for Voice over WLAN service.

B. Implement the wireless network with the restraints and utilize high-gain antenna to provide overlapping cellcoverage at sufficient SNR to provide for Voice over WLAN service.

C. Inform the customer that the network will not likely function as desired and a post install survey with thepossibility of some new cable would be recommended.

D. Inform the customer that it is not possible to provide coverage and quality for Voice over WLAN usingexisting AP locations and an entire overbuild will be necessary.

Answer: C

Q6. An engineer is conducting a location readiness test and wants a selected point to be considered location-ready. Which three possible configurations reflect the minimum number of APs needed? (Choose three.)

A. One AP is resident in each quadrant surrounding the point-in-question.

B. One AP per 1400 sq. ft. on the map.

C. Two APs are resident in each quadrant surrounding the point-in- question.

D. Four APs are deployed on the floor.

E. Three APs are within 70 feet (21 meters) of the point-in- question

F. Three APs are deployed on the floor.

Answer: A,D,E

Explanation:

A point in a WLAN deployment is location ready if the following are all determined to be true:

At least four access points are deployed on the floor.

At least one access point is found to be resident in each quadrant surrounding the point-in- QUESTION NO:. At least one access point residing in each of at least three of the surrounding quadrants is located within 70 feet of the point-in-QUESTION NO:.

Reference:

http://www.cisco.com/c/en/us/td/docs/solutions/Enterprise/Borderless_Networks/Unified_Access/CMX/CMX_LocFund.pdf

Q7. A customer wants to implement a wireless network in a historic location, but is concerned about the structural and aesthetic impact to the facility. Which benefit of using wireless mesh addresses these concerns?

A. Power is required only at the installation location.

B. The APs do not have LED lights.

C. More wireless channels can be supported.

D. APs do not need network connections.

Answer: D

Q8. An engineer is assigned to assist a customer by estimating the number of access points needed to provide voice-grade wireless coverage in a carpeted office space. How many access points should be estimated to cover this space of roughly 38,000 square feet?

A. 17

B. 10

C. 6

D. 13

Answer: D

Explanation:

The rule of thumb coverage plan is 1 AP per 5,000 square feet for data and 1 per 3,000 square feet for voice and location services.

Reference: http://www.cisco.com/c/en/us/td/docs/wireless/technology/apdeploy/8-0/Cisco_Aironet_3700AP.html

Q9. A network engineer wants the DSCP marking to align with the 802.11e access category video. What will this marking be?

A. 34

B. AF31

C. 4

D. 5

Answer: A

Q10. You have a customer that is building a new campus of four 3-story buildings that you have just completed the site survey for. The customer is interested in the mount of rack space they will need to allocate in either the building MDF or in the data center for controllers. Each building is going to require 75 APs to support voice and data. How should the controllers be deployed to provide the least number of controllers, the highest redundancy, and the easiest management?

A. Use the centralized deployment method in the data center with the N + N redundancy method.

B. Use the centralized deployment method in the data center with the N + 1 redundancy method

C. Use the centralized deployment method in the data center with the 1 + 1 redundancy method and clientSSO.

D. Use the distributed deployment method in each building MDF with the N + 1 redundancy method.

E. Use the distributed deployment method in each building MDF with the N + N + 1 redundancy method.

F. Use the distributed deployment method in each building MDF with the N + N redundancy method.

Answer: C