300-410 Guide
Improve 300-410 Courses 2021
Posted by Alex Baker to Cisco 300-410
Follow @2passeasy
It is impossible to pass Cisco 300-410 exam without any help in the short term. Come to Examcollection soon and find the most advanced, correct and guaranteed Cisco 300-410 practice questions. You will get a surprising result by our Latest Implementing Cisco Enterprise Advanced Routing and Services (ENARSI) practice guides.
Free demo questions for Cisco 300-410 Exam Dumps Below:
NEW QUESTION 1
Which statement about IPv6 ND inspection is true?
- A. It learns and secures bindings for stateless autoconfiguration addresses in Layer 3 neighbor tables.
- B. It learns and secures bindings for stateless autoconfiguration addresses in Layer 2 neighbor tables.
- C. It learns and secures bindings for stateful autoconfiguration addresses in Layer 3 neighbor tables.
- D. It learns and secures bindings for stateful autoconfiguration addresses in Layer 2 neighbor tables.
Answer: B
NEW QUESTION 2
Refer to the exhibit.
An IP SLA was configured on router R1 that allows the default route to be modified in the event that Fa0/0 loses reachability with the router R3 Fa0/0 interface. The route has changed to flow through
router R2. Which debug command is used to troubleshoot this issue?
- A. debug ip flow
- B. debug ip sla error
- C. debug ip routing
- D. debug ip packet
Answer: C
NEW QUESTION 3
Refer to the exhibit.
An engineer is trying to block the route to 192.168.2.2 from the routing table by using the
configuration that is shown. The route is still present in the routing table as an OSPF route. Which action blocks the route?
- A. Use an extended access list instead of a standard access list.
- B. Change sequence 10 in the route-map command from permit to deny.
- C. Use a prefix list instead of an access list in the route map.
- D. Add this statement to the route map: route-map RM-OSPF-DL deny 20.
Answer: B
NEW QUESTION 4
Refer to the exhibit.
An engineer is trying to connect to a device with SSH but cannot connect. The engineer connects by using the console and finds the displayed output when troubleshooting. Which command must be used in configuration mode to enable SSH on the device?
- A. no ip ssh disable
- B. ip ssh enable
- C. ip ssh version 2
- D. crypto key generate rsa
Answer: D
NEW QUESTION 5
Which command displays the IP routing table information that is associated with VRF-Lite?
- A. show ip vrf
- B. show ip route vrf
- C. show run vrf
- D. show ip protocols vrf
Answer: B
NEW QUESTION 6
Drag and drop the MPLS VPN concepts from the left onto the correct descriptions on the right.
- A. Mastered
- B. Not Mastered
Answer: A
Explanation: 
NEW QUESTION 7
Refer to the exhibit.
Which configuration configures a policy on R1 to forward any traffic that is sourced from the 192.168.130.0/24 network to R2?
- A. Option A
- B. Option B
- C. Option C
- D. Option D
Answer: D
NEW QUESTION 8
Refer to the exhibit.
What is the result of applying this configuration?
- A. The router can form BGP neighborships with any other device.
- B. The router cannot form BGP neighborships with any other device.
- C. The router cannot form BGP neighborships with any device that is matched by the access list named “BGP”.
- D. The router can form BGP neighborships with any device that is matched by the access list named “BGP”.
Answer: D
NEW QUESTION 9
Which configuration enabled the VRF that is labeled “Inet” on FastEthernet0/0?
- A. R1(config)# ip vrf InetR1(config-vrf)#ip vrf FastEthernet0/0
- B. R1(config)#ip vrf Inet FastEthernet0/0
- C. R1(config)# ip vrf InetR1(config-vrf)#interface FastEthernet0/0 R1(config-if)#ip vrf forwarding Inet
- D. R1(config)#router ospf 1 vrf InetR1(config-router)#ip vrf forwarding FastEthernet0/0
Answer: C
NEW QUESTION 10
Refer to the exhibit.
Why is the remote NetFlow server failing to receive the NetFlow data?
- A. The flow exporter is configured but is not used.
- B. The flow monitor is applied in the wrong direction.
- C. The flow monitor is applied to the wrong interface.
- D. The destination of the flow exporter is not reachable.
Answer: D
NEW QUESTION 11
When provisioning a device in Cisco DNA Center, the engineer sees the error message “Cannot select the device. Not compatible with template”.
What is the reason for the error?
- A. The template has an incorrect configuration.
- B. The software version of the template is different from the software version of the device.
- C. The changes to the template were not committed.
- D. The tag that was used to filter the templates does not match the device tag.
Answer: B
NEW QUESTION 12
Refer to the exhibit.
An administrator that is connected to the console does not see debug messages when
remote users log in. Which action ensures that debug messages are displayed for remote logins?
- A. Enter the transport input ssh configuration command.
- B. Enter the terminal monitor exec command.
- C. Enter the logging console debugging configuration command.
- D. Enter the aaa new-model configuration command.
Answer: B
NEW QUESTION 13
Which protocol is used to determine the NBMA address on the other end of a tunnel when mGRE is used?
- A. NHRP
- B. IPsec
- C. MP-BGP
- D. OSPF
Answer: D
NEW QUESTION 14
Drag and drop the DHCP messages from the left onto the correct uses on the right.
- A. Mastered
- B. Not Mastered
Answer: A
Explanation: 
NEW QUESTION 15
Which attribute eliminates LFAs that belong to protected paths in situations where links in a network are connected through a common fiber?
- A. shared risk link group-disjoint
- B. linecard-disjoint
- C. lowest-repair-path-metric
- D. interface-disjoint
Answer: A
NEW QUESTION 16
What is a prerequisite for configuring BFD?
- A. Jumbo frame support must be configured on the router that is using BFD.
- B. All routers in the path between two BFD endpoints must have BFD enabled.
- C. Cisco Express Forwarding must be enabled on all participating BFD endpoints.
- D. To use BFD with BGP, the timers 3 9 command must first be configured in the BGP routing process.
Answer: C
NEW QUESTION 17
Refer to the exhibit.
Which configuration denies Telnet traffic to router 2 from 198A:0:200C::1/64?
- A. Option A
- B. Option B
- C. Option C
- D. Option D
Answer: A
NEW QUESTION 18
Which command allows traffic to load-balance in an MPLS Layer 3 VPN configuration?
- A. multi-paths eibgp 2
- B. maximum-paths 2
- C. maximum-paths ibgp 2
- D. multi-paths 2
Answer: B
NEW QUESTION 19
Drag and drop the packet types from the left onto the correct descriptions on the right.
- A. Mastered
- B. Not Mastered
Answer: A
Explanation: 
NEW QUESTION 20
Refer to the exhibit.
Users report that IP addresses cannot be acquired from the DHCP server. The DHCP
server is configured as shown. About 300 total nonconcurrent users are using this DHCP server, but none of them are active for more than two hours per day. Which action fixes the issue within the current resources?
- A. Modify the subnet mask to the network 192.168.1.0 255.255.254.0 command in the DHCP pool
- B. Configure the DHCP lease time to a smaller value
- C. Configure the DHCP lease time to a bigger value
- D. Add the network 192.168.2.0 255.255.255.0 command to the DHCP pool
Answer: B
NEW QUESTION 21
Refer to the exhibit.
Which interface configuration must be configured on the spoke A router to enable a dynamic DMVPN tunnel with the spoke B router?
- A. Option A
- B. Option B
- C. Option C
- D. Option D
Answer: A
NEW QUESTION 22
Refer to the exhibit.
An engineer is trying to configure local authentication on the console line, but the device is trying to authenticate using TACACS+. Which action produces the desired configuration?
- A. Add the aaa authentication login default none command to the global configuration.
- B. Replace the capital “C” with a lowercase “c” in the aaa authentication login Console local command.
- C. Add the aaa authentication login default group tacacs+ local-case command to the global configuration.
- D. Add the login authentication Console command to the line configuration
Answer: D
NEW QUESTION 23
Which method changes the forwarding decision that a router makes without first changing the routing table or influencing the IP data plane?
- A. nonbroadcast multiaccess
- B. packet switching
- C. policy-based routing
- D. forwarding information base
Answer: C
NEW QUESTION 24
Refer to the exhibit.
R2 is a route reflector, and R1 and R3 are route reflector clients. The route reflector learns
the route to 172.16.25.0/24 from R1, but it does not advertise to R3. What is the reason the route is not advertised?
- A. R2 does not have a route to the next hop, so R2 does not advertise the prefix to other clients.
- B. Route reflector setup requires full IBGP mesh between the routers.
- C. In route reflector setup, only classful prefixes are advertised to other clients.
- D. In route reflector setups, prefixes are not advertised from one client to another.
Answer: A
NEW QUESTION 25
......
Recommend!! Get the Full 300-410 dumps in VCE and PDF From Dumpscollection, Welcome to Download: http://www.dumpscollection.net/dumps/300-410/ (New 58 Q&As Version)
To know more about the 300-410, click here.