400-201 Guide

400-201 Exam Royal Pack (In Stock.)

  • Cisco
  • Exam Number/Code 400-201
  • Product Name CCIE SP CCIE Service Provider Written Exam
  • Questions and Answers
  • 699 Q&As
  • Last Updated
  • Jan 15,2018
  • List Price
  • $128.99
  • Price
  • Today 49.99 USD

Free TrialVersion: demo Buy Now 50% OFF

What Does 400-201 training Mean?

We provide real 400-201 exam questions and answers braindumps in two formats. Download PDF & Practice Tests. Pass Cisco 400-201 Exam quickly & easily. The 400-201 PDF type is available for reading and printing. You can print more and practice many times. With the help of our Cisco 400-201 dumps pdf and vce product and material, you can easily pass the 400-201 exam.

Q71. Refer to the exhibit. Both MPLS TE tunnel 14 and MPLS TE tunnel 124 pass over the same physical links. Which configuration on R1 enables TE 14 to be the primary tunnel and TE 124 to become active when TE 14 is admin disabled? 

A. Interface Tunnel14 

tunnel mpls traffic-eng priority 3 1 

Interface Tunnel124 

tunnel mpls traffic-eng priority 5 4 

B. Interface Tunnel14 

tunnel mpls traffic-eng priority 4 1 

`Interface Tunnel124 

tunnel mpls traffic-eng priority 3 2 

C. Interface Tunnel14 

tunnel mpls traffic-eng priority 7 7 

Interface Tunnel124 

tunnel mpls traffic-eng priority 1 1 

D. Interface Tunnel14 

tunnel mpls traffic-eng priority 3 2 

Interface Tunnel124 

tunnel mpls traffic-eng priority 4 1 


Q72. Two routers that are running MPLS and LDP have multiple links that than connect them to each other. An engineer wants to ensure that the label bindings are not flushed from the LIB if one of the links fails. Which configuration meets this requirement? 

A. the mpls ldp neighbor targeted command 

B. the mpls ip command on a Cisco MPLS TE tunnel 

C. the mpls ldp discovery targeted-hello accept command 

D. the mpls ldp session protection command 





Q73. Refer to the exhibit. A network engineer must configure BFD for IS-IS between R1 and R2. In case the primary link fails, the convergence time should be less than a second. 

Which two IOS commands are required to meet this requirement? (Choose two.) 

A. isis bfd 

B. bfd minimum-interval 250 

C. bfd interval 250 min_rx 250 multiplier 3 

D. bfd multiplier 3 

E. bfd interval 250 min_rx 250 multiplier 4 

F. bfd fast-detect ipv4 

Answer: C,F 

Explanation: http://www.cisco.com/c/en/us/td/docs/routers/xr12000/software/xr12k_r4-3/routing/command/reference/b_routing_cr43xxr12k/b_routing_cr43xxr12k_chapter_010.ht ml#wp3058619742 

Q74. Refer to the exhibit. An MPLS Layer 3 VPN service has been provisioned for a customer. What will be the ToS value at Site-B for the exceeded traffic that it is sent from Site-A with ToS 2? 

A. 0 

B. 2 

C. 3 

D. 4 

E. No exceeded traffic will reach Site-B. 


Q75. Refer to the exhibit. The Service Provider does not have IPv6 support in the core, however it does have MPLS support. Customer requires IPv6 connectivity in all sites including Internet access. Without a requirement to create VRF, which method is preferred to support IPv6 traffic between these sites? 

A. 6VPE 


C. L2TPv3 


E. 6CE 

F. 6PE 



http://www.cisco.com/en/US/products/sw/iosswrel/ps1835/products_data_sheet09186a008 052edd3.html 

Q76. Which are the three characteristics of SDR? (Choose three) 

A. The logical router can span across chassis. 

B. Each logical router has a distinct fabric and system controller module. 

C. Owner SDR can be reloaded, without affecting all non-SDRs. 

D. The logical router has dedicated route processor. 

E. The logical router can share line cards. 

F. The fabric and system controller module are shared by all logical routers. 

Answer: A,D,F 

Q77. An engineer is implementing an MPLS within the core of the Service Provider network. What two components are required to build the control and data plane for MPLS Label Switched Paths? (Choose two.) 






Answer: B,C 

Q78. On a Cisco ASR 1000 Series, which hardware component is used to build and distribute the forwarding plane information to all line cards? 

A. RP 






Drag and drop the IPFIX terminology on the left to the correct description on the right. Not all options will be used. 


Q80. Which two statements about 10 Gigabit Ethernet WAN PHY mode are true? (Choose two.) 

A. The signal maps to an OC-192c/STM-64c payload. 

B. The nominal speed is 9.95328 Gbps. 

C. It is compatible with Packet Ethernet over SONET. 

D. The signal maps to an OC-768c/STM-256c payload. 

E. It is compatible with Packet over SONET. 

F. The nominal speed is 10.3125 Gbps. 

Answer: A,B 

Explanation: https://en.wikipedia.org/wiki/10_Gigabit_Ethernet 

To know more about the 400-201, click here.

Tagged as : Cisco 400-201 Dumps, Download 400-201 pdf, 400-201 VCE, 400-201 pass4sure, examcollection 400-201